Модуль 4G
Модуль 4G

Ebyte — национальное высокотехнологичное предприятие, специализирующееся на исследованиях и разработках беспроводных модулей и промышленных IoT-терминалов.

How to Let the Wireless Module Transmit Farther?

From the power supply side, wireless modules are quite sensitive to power supply noise, especially to glitch voltages and other high-frequency harmonics.

A little tweak on the power supply

From the power supply side, wireless modules are quite sensitive to power supply noise, especially to glitch voltages and other high-frequency harmonics. If proper power supply decoupling is not adopted, voltage glitches on the power supply line will be caused, which may reach the RF power supply pin and affect the RF signal. 4G ДТУ

The wireless module is also a load and needs to dissipate a certain amount of power consumption. When selecting the power supply, it is necessary to consider whether the power supply capacity of the power supply is sufficient for the wireless module and other power-consuming units, and at the same time ensure a certain margin (at least 30% margin).

Therefore, when planning wireless transmission products at the beginning, make a little adjustment in the power supply, and select a power supply chip with a small ripple coefficient and a suitable load current as the power supply unit of the wireless module to ensure the stability of the wireless transmission system. The transmission distance will be farther.

A little tweaking of the transmitter and receiver

First of all, you need to consider the application scenario and determine the distance to be transmitted; if you need to perform wireless transmission of at least 7~8km, it is recommended to use at least a wireless module with a transmit power of 30dBm (1W) and high receiving sensitivity, that is, whether the wireless module has a power amplifier. (PA) and low noise amplifier (LNA), otherwise long-distance wireless transmission cannot be achieved. НБ ДТУ

A little tweak to the antenna

The gain of the wireless communication system is equal to the sum of the transmit power of the wireless module and the gain of the antenna, so the gain of the antenna has a great relationship with the transmission distance of the wireless module. When the module and the antenna are matched, the higher the gain of the antenna, the longer the transmission distance of the wireless module. The general small suction cup gain is only about 2.0dBi, and some better outdoor large antennas can achieve a gain of about 5dBi. If the effect of data transmission with a low-gain antenna and a wireless module is unsatisfactory, an antenna with a higher gain can be replaced, and the wireless module will transmit farther. At the same time, it is also necessary to pay attention to the directionality and installation method of the antenna. The antenna should be erected as high as possible, and the antenna connected to the wireless module should be placed in the same horizontal plane and parallel state, so that the sensing surface of the wireless signal transmission and reception is the largest, and the transmission and reception The received electromagnetic wave signal strength is the largest, so that the wireless transmission distance is longer.

A little tweak to the transmission path

The wireless data communication of the wireless module is realized by the linear transmission of wireless electromagnetic waves in the air, so the occlusion of obstacles has a great influence on the wireless transmission, especially the obstacles of metal objects, which not only block the wireless transmission signal, but also absorb the wireless transmission. And reflected electromagnetic wave signal, reduce radiation efficiency. Therefore, the biggest obstacle to wireless transmission is actually metal, houses, woods, grass, sea level and other objects that can block.

Make a little adjustment to the working frequency

Wireless channels are relatively crowded, especially the ISM frequency band. During the actual installation of communication equipment, spectrum surveys can be made on the local electromagnetic environment to select relatively “clean” frequency points to avoid unnecessary interference. At the same time, strict compliance with Local laws and regulations for frequency planning.

A little tweak to the structure

For the case where the antenna is placed in the casing, it is suggested that, if the structure allows, placing the antenna outside the casing can increase the radiated signal strength and increase the transmission distance. Under the conditions that the structure does not allow, adjust the matching between the antenna and the module to increase the gain of the entire transmission system.

Сервер с одним последовательным портом

In general, the wireless transceiver module should achieve the ideal wireless transmission effect:

1. Do the preliminary planning and selection, mainly for the power supply and the wireless module to be used.

2. Elevate the antenna placement point at both ends of the transceiver or offset the placement point of the antenna to reduce the occlusion of obstacles, reduce the attenuation of electromagnetic wave signals, and reduce the blind area of ​​wireless signals.

3. It is recommended that the antennas of the transmitter and receiver be placed in the same horizontal plane and parallel.

4. Use a high-gain antenna that matches the wireless module and the user's application scenario.

CC BY-NC-ND 2.0 版权声明

喜欢我的文章吗?
别忘了给点支持与赞赏,让我知道创作的路上有你陪伴。

加载中…

发布评论